GXW4024 A legérdekesebbnek ítélt tulajdonságok Előnyök ára ~750 USD magyországon már bruttó 188300 HUF-tól kapható azaz ~8000 HUF / FXS port. Ha egy ip telefon + poe switch port árát összeszámoljuk akkor ennél egy kedvező számot kapunk persze ne feledjük ez analóg. proxy nélküli is működik pl. analóg vonalak meghosszabbítása esetén lehet érdekes lásd: Using GXW-Series to extend analog lines without SIP server http://grandstream.com/support/gxw_series/general/documents/gxw_wp_extending_analog_lines.pdf automatikus számtárcsázás kagylófelemelésre visszaesés fxo gw-re hangnélküli működés, passzív hűtés. Nincs benne ventilátor! fogyasztás ~30Watt sip session timer támogatás, beragadt hívások bontására boot idő ~1 perc Gyengeségek Nem működiknek a magyar ékezetes karakterek SIP AoR displaynmae mezőben. Debug nem túl részletes nem derül ki sok minden belőle RFC3263 nem derült ki működik-e. Választható az hogy NAPTR + SRV vagy SRV vagy A rekordot oldjon fel. FAQ szerint én nem próbáltam de csak két párhuzamos T.38-as fax hívást tud e felett passthrough módban üzemel http://grandstream.com/GXW410xFAQs.html#twelve How many simultaneous fax calls can the GXW40xx handle?? The GXW40xx series can handle up to two T.38 simultaneous sessions and G.711 Pass-Through on the remaining ports. Dokumentáció nagyon elnagyolt és hiányos!! Dokumentációban Nem találtam meg a bejátszott hangok bállításának lehetőségét http://www.itu.int/ITU-T/inr/forms/files/tones-0203.pdf Call Progress Tones: [Syntax: ch x-y: f1=val@vol,f2=val@vol,c=on1/off1-on2/off2-on3/off3;[...]) Note : f1,f2-frequency(Hz); vol-volume(dB); c-cadence(10ms, 0-continuous)] dialplan a dialpan megadása kezdetleges. per FXS port nem lehet megadni külön dialplant csak provisioning Az xml config file formátuma nem dokumentált, így nem tudni az mit is tud. config file provisioning nehézkes mert mindig le kell futatni rá a grandstream oldaláról letölthető java-s tool-t, ami egy kulccsal titkosítja. Egyáltalán nem rugalmas, elég alap megoldás!! MWI: nem adható meg külön SIP URI minden módosítás után újra kell indítani hogy a módosítás életbe lépjen. nincs IPv6 (De ez sajnos általánosan igaz szinte minden voip eszközre) Egyéb TLS+SRTP-t tesztelve (egyidőben egyetlen FXS protot használva) nem tapasztaltam hibát. magyar dialplan {*x+|00x+|15xxx+|13[01]x+|06[237]0xxxxxxx|06xxxxxxxx|[1-9]xxxxx|17xxx|118xx|14[5-9]xx|116xxx|17xx|18xx|14[0-4]x|12xx|19[1234789]|17x|18x|10[457]|112} Provisioning minta A csengetési hangokat/visszhangopkat/idősítéseket/frekvenciákat igyekeztem a magyarosítani. A file letölthető innen is gxw4024_config_1.0.3.10_hu.txt ################################################################################################ ## Configuration template for GXW40XX firmware version 1.0.3.10 ################################################################################################ ############################################################################## ## Advanced Settings. ############################################################################## # Enable Provider Lock. 0 - No, 1 - Yes. P9999 = 0z # Provider Lock Key. A string of up to 16 bytes. P9998 = nouse # Provider Authentication. A string of up to 16 bytes P9997 = nouse # Password for configuration file authentication P1 = # Admin password for web interface P2 = admin # Layer 3 QoS (IP Diff-Serv or Precedence value for RTP) P38 = 46 # Layer 2 QoS. 802.1Q/VLAN Tag (VLAN classification for RTP) P51 = 0 # Layer 2 QoS. 802.1p priority value (0 - 7) P87 = 5 # 802.1p priority value (NATed traffic) ** This doesn't apply to the GXW4024 P230 = 0 # STUN server P76 = stun.xten.com # Keep-alive interval (in seconds. default 20 seconds) P84 = 20 # Use STUN to detect network connectivity. 0 - No, 1 - Yes. P474 = 0 # Total STUN response misses to restart DHCP (mininum=3 default=5) P475 = 3 #------------------------------------------------------------------------------- # Firmware Upgrade #------------------------------------------------------------------------------- # Firmware Upgrade and Privisioning. 0 - TFTP Upgrade, 1 - HTTP Upgrade, 2 - HTTPS Upgrade. P212 = 1 # Firmware Server Path P192 = 72.172.83.110 # Config Server Path P237 = 192.168.1.1 # XML Config File Password P1359 = # HTTP/HTTPS User Name P1360 = # HTTP/HTTPS Password P1361 = # Firmware File Prefix P232 = # Firmware File Postfix P233 = # Config File Prefix P234 = # Config File Postfix P235 = # Allow DHCP Option 66 to override server. 0 - No, 1 - Yes. Default is Yes. # When set to Yes(1), it will override the configured provision path and method. P145 = 0 # Automatic Upgrade. 0 - No, 1 - Check daily, 2 - Check weekly, 3 - Check every () minutes. Default is No. P194 = 1 # Check for new firmware/config file every () minutes, unit is in minute, minimum 60 minutes, default is 7 days. P194 = 3 P193 = 10080 # Automatic Upgrade. Daily at hour(0-23). P194 = 1 P285 = 1 # Automatic Upgrade. Weekly on day (0-6). P194 = 2 P286 = 1 # Use firmware pre/postfix to determine if f/w is required # 0 = Always Check for New Firmware # 1 = Check New Firmware only when F/W pre/suffix changes # 2 = Always Skip the Firmware Check # For Firmware only. P238 = 0 # Authenticate Config File. 0 - No , 1 - Yes P240 = 0 # Firmware Key (AES 128, in Hexadecimal Representation) P242 = # SSL Certificate #P280 = # SSL Private Key #P279 = # SSL Private Key Password #P281 = # ACS URL P4503 = # ACS Username P4504 = # ACS Password P4505 = # Periodic Inform Enable 0 - No, 1 - Yes (default is No) P4506 = 0 # Periodic Inform Interval (default is 300) P4507 = 300 # Conncetion Request Username P4511 = # Connection Request Password P4512 = # System Ring Cadence P4040 = c=1000/4000; #------------------------------------------- # Call Progress Tones #------------------------------------------- # Dial Tone P4000 = f1=425@-13,c=0/0; # Ringback Tone P4001 = f1=425@-19,c=1240/3750; # Busy Tone P4002 = f1=425@-24,c=300/300; # Reorder Tone P4003 = f1=300@-24,f2=425@-24,c=200/200; # Confirmation Tone P4004 = f1=300@-11,f2=425@-11,c=1000/200; # Call Waiting tone P4005 = f1=425@-13,c=40/1960; #-------------------------------------------- # Lock keypad update. 0 - No, 1 - Yes. P88 = 1 # Disable voice prompt. 0 - No, 1 - Yes. P253 =0 # Disable Direct IP Call. 0 - No, 1 - Yes. P277 = 1 # Life line mode. 0 - Auto, 1 - Always disconnected, 2 - Always connected P891 = 0 # Failover to FXO Gateway. 0 - Disable, 1 - Enable P4205 = 0 # FXO Gateway. URI or IP address. P4206 = # NTP Server P30 = hu.pool.ntp.org # Syslog Server (name of the server, max length is 64 charactors) P207 = 192.168.1.1 # Syslog Level (Default setting is NONE) # 0 - NONE, 1 - DEBUG, 2 - INFO, 3 - WARNING, 4 - ERROR P208 = 1 # Primary RADIUS Server #P4550 = # Primary RADIUS Auth Port (default 1812). P4551 = 1812 # Primary RADIUS Acct Port (default 1813). P4552 = 1813 # Primary RADIUS Server Secret P4553 = # Secondary RADIUS Server #P4554 = # Secondary RADIUS Auth Port (default 1812). P4555 = 1812 # Secondary RADIUS Acct Port (default 1813). P4556 = 1813 # Secondary RADIUS Server Secret P4557 = # RADIUS Timeout (default 2). P4558 = 2 # RADIUS Retry (default 3). P4559 = 3 ############################################################################## ## Profile 1 Settings ############################################################################## # Profile Active. 0 - no, 1 - yes P271 = 1 # Primary SIP Server P47 = 192.168.1.1 # Failover SIP Server P967 = # Prefer Primary SIP Server. 0 - No, 1 - Yes. P4567 = 0 # Outbound Proxy P48 = 192.168.1.1 # SIP Transport. 0 - UDP, 1 - TCP, 2 - TLS P130 = 0 # NAT Traversal (STUN). 0 - No, 2 - No but send keep-alive, 1 - Yes P52 = 0 # Visual MWI type: 0 - FSK, 1 - Neon P4371 = 0 # DNS Mode. 0 - A Record, 1 - SRV, 2 - NAPTR/SRV. P103 = 0 # SIP User ID is phone number. 0 - no, 1 - yes P63 = 0 # SIP Registration. 0 - no, 1 - yes P31 = 1 # Unregister On Reboot. 0 - no, 1 - yes P81 = 0 # Outgoing call without Registration. 0 - no, 1 - yes P109 = 1 # Register Expiration (in minutes. default 1 hour, max 45 days) P32 = 60 # Registration Retry Wait Time (in seconds. Between 1-3600, default is 30) P138 = 20 # Local SIP port (default 5060) P40 = 5060 # Local RTP port (1024-65535, default 5004) P39 = 5004 # Use Random Port. 0 - no, 1 - yes P78 = 0 # Refer-To Use Target Contact. 0 - no, 1 - yes P135 = # Transfer on Conference Hangup. 0 - no, 1 - yes P4560 = 0 # Remove OBP from Route Header. 0 - no, 1 - yes P4562 = 0 # Support SIP Instance ID. 0 - no, 1 - yes P288 = 1 # Validate Incoming Message. 0 - No, 1 - Yes P4340 = 0 # Check SIP Incoming UserID. 0 - No, 1 - Yes (no direct IP calling if Yes) P258 = 0 # Allow Incoming SIP Messages from SIP Proxy Only: P243 = 0 # SIP T1 Timeout. RFC 3261 T1 value (RTT estimate) # 50 - 0.5 sec, 100 - 1 sec, 200 - 2 sec, 400 - 4 sec, 800 - 8 sec. Default 100. P209 = 100 # SIP T2 Interval. RFC 3261 T2 value. The maximum retransmit interval for non-INVITE requests and INVITE responses. # 200 - 2 sec, 400 - 4 sec, 800 - 8 sec, 1600 - 16 sec, 3200 - 32 sec. Default 400. P250 = 400 # DTMF Payload Type P79 = 101 # Preferred DTMF method. # 100 - In-audio, 101 - RFC2833, 102 - SIP INFO # Priority 1 P850 = 101 # Priority 2 P851 = 102 # Priority 3 P852 = 100 # Send Flash Event. 0 - no, 1 - yes P74 = 0 # Enable Call Features. 0 - no, 1 - yes P191 = 1 # Proxy-Require (A SIP extension to enable firewall penetration) P197 = # Use NAT IP. This will enable our SIP client to use this IP in the SIP message. Example 64.3.153.50. P101 = # Distinctive Ring Tone # 0 - Ring Tone 1, 1 - Ring Tone 2, 2 - Ring Tone 3, 3 - Ring Tone 4, 4 - Ring Tone 5, # 5 - Ring Tone 6, 6 - Ring Tone 7, 7 - Ring Tone 8, 8 - Ring Tone 9, 9 - Ring Tone 10 # Distinctive Ring Tone Choice 1 P870 = 0 # Choice 1 incoming caller ID P871 = # Distinctive Ring Tone Choice 2 P872 = 0 # Choice 2 incoming caller ID P873 = # Distinctive Ring Tone Choice 3 P874 = 0 # Choice 3 incoming caller ID P875 = # Disable Call Waiting. 0 - no, 1 - yes P91 = 0 # Disable Call-Waiting Caller ID. 0 - no, 1 - yes P714 =0 # Disable Call-Waiting Tone. 0 - no, 1 - yes P186 = 0 # Disable Reminder Ring for On-Hold Call: P4360 = 0 # Disable Visual MWI. 0 - No, 1 - Yes P855 = 0 # Ring Timeout. (10-300, default is 60 seconds) P185 = 60 # Hunting Group Ring Timeout. (5-300, default is 20 seconds) P4330 = 20 # Delayed Call Forward Wait Time. Allowed range 1-120, in seconds. Default 20 seconds. P139 = 20 # No Key Entry Timeout. Default - 4 seconds. P85 = 4 # Early Dial. 0 - No, 1 - Yes (use "Yes" only if proxy supports 484 response). 0 - no, 1 - yes P29 = 0 # Dial Plan Prefix.(this prefix string is added to each dialed number) P66 = # Use # as Dial Key (if set to Yes, "#" will function as the "(Re-)Dial" key). 0 - no, 1 - yes P72 = 1 # Dial Plan P4200 = {*x+|00x+|15xxx+|13[01]x+|06[237]0xxxxxxx|06xxxxxxxx|[1-9]xxxxx|17xxx|118xx|14[5-9]xx|116xxx|17xx|18xx|14[0-4]x|12xx|19[1234789]|17x|18x|10[457]|112} # SUBSCRIBE for MWI. 0 - No, 1 - Yes. P99 = 1 # Send Anonymous. 0 - no, 1 - yes (caller ID will be blocked if set to Yes). P65 = 0 # Anonymous Call Rejection. 0 - No, 1 - Yes. P129 = 0 # Special Feature # 100 - Standard, 108 - CBCOM, 109 - RNK, 111 - Huawei P198 = 100 # Session Expiration (in seconds. default 180 seconds. Allowed value: 90-65535) P260 = 180 # Minimum SE (in seconds. default 90 seconds, must be lower than or equal to P260) P261 = 90 # Caller Request Timer (Request for timer when calling) 0 - no, 1 - yes P262 = 0 # Callee Request Timer (Request for timer when called. i.e. if remote party supports timer but did not request for one) 0 - no, 1 - yes P263 = 0 # Force Timer (Still use timer when remote party does not support timer) 0 - no, 1 - yes P264 = 0 # UAC Specify Refresher. 0 - omit, 1 - UAC, 2 - UAS P266 = 0 # UAS Specify Refresher. 1 - UAC, 2 - UAS P267 = 1 # Force INVITE (Always refresh with INVITE instead of UPDATE even when remote party supports UPDATE) 0 - no, 1 - yes P265 = 0 # Send Re-INVITE After Fax. 0 - No, 1 - Yes P4367 = 0 #------------------------------------------------------------------------------- # Codec/Voice Quality settings #------------------------------------------------------------------------------- # Use First Matching Vocoder in 200OK SDP. 0 - No, 1 - Yes P4363 = 0 # Preferred Vocoder # 0 - PCMU, 8 - PCMA, 4 - G.723, 18 - G.729, 2 - G.726-32, 100 - AAL2-G.726-16, # 102 - AAL2-G.726-24, 104 - AAL2-G726-32, 103 - AAL2-G.726-40, 98 - iLBC, 99 - G.729E # Choice 1. P57 = 8 # Choice 2. P58 = 0 # Choice 3. P59 = 4 # Choice 4. P60 = 18 # Choice 5. P61 = 2 # Choice 6. P62 = 98 # Choice 7. P46 = 103 # Choice 8. P98 = 99 # G723 rate. 0 - 6.3kbps encoding rate, 1 - 5.3kbps encoding rate P49 = 0 # iLBC Frame Size. 0 - 20ms(default), 1 - 30ms. P97 = 0 # iLBC payload type. Between 96 and 127, default is 97. P96 = 97 # AAL2-G.726-16 Payload type. (between 96 and 127, default is 100) P125 = 100 # AAL2-G.726-24 Payload type. (between 96 and 127, default is 99) P126 = 99 # AAL2-G726-32 payload type. (between 96 and 127, default is 104) P127 = 104 # AAL2-G.726-40 Payload type. (between 96 and 127, default is 103) P128 = 103 # G.729E Payload type. (between 96 and 127, default is 102) P124 = 102 # VAD. 0 - No, 1 - Yes P50 = 0 # Symmetric RTP. 0 - No, 1 - Yes P291 = 0 # FAX Mode. 0 - T.38 (Auto Detect), 1 - Pass Through P228 = 0 # Fax Tone Detection Mode. 1 - Caller, 0 - Callee, 2 - Caller or Callee P894 = 0 # Jitter Buffer Type. 0 - Fixed, 1 - Adaptive P133= 1 # Jitter Buffer Length. 0 - Low, 1 - Medium, 2 - High P132 = 1 # SRTP Mode # 0 = Disabled # 1 = Enabled but not forced # 2 = Enabled and forced P183 = 1 #--------------------------------------------------------- # SLIC Setting # 0 - USA, 1 - AUSTRIA, 2 - BELGIUM, 3 - FINLAND, 4 - FRANCE, 5 - GERMANY # 6 - GREECE, 7 -ITALY, 8 - JAPAN, 9 - NORWAY, 10 - SPAIN, 11 - SWEDEN, # 12 - UK, 13 - AUSTRALIA/NEW ZEALAND P854 = 4 # Caller ID Scheme # 0 - Bellcore/Telcordia # 1 - ETSI-FSK during ringing # 2 - ETSI-FSK prior to ringing with DTAS # 3 - ETSI-FSK prior to ringing with LR # 4 - ETSI-FSK prior to ringing with RP # 5 - ETSI-DTMF during ringing # 6 - ETSI-DTMF prior to ringing with DTAS # 7 - ETSI-DTMF prior to ringing with LR # 8 - ETSI-DTMF prior to ringing with RP # 9 - SIN 227 - BT # 10 - NTT Japan P853 = 1 # Polarity Reversal. 0 - No, 1 - Yes P205 = 0 # Loop Current Disconnect. 0 - No, 1 - Yes P892 = 0 # Loop Current Disconnect Duration. In 100 - 10000 milliseconds range, default is 200. P856 = 200 # Hook Flash Timing. In 40-2000 milliseconds range # minimum P251 = 40 # maximum P252 = 350 # On Hook Timing. (In 40-2000 milliseconds range, default is 400) P833 = 400 # Gain: # TX # +6dB # +4dB # +2dB # 0dB # -2dB # -4dB # -6dB P247 = 0 # RX # +6dB # +4dB # +2dB # 0dB # -2dB # -4dB # -6dB P249 = 0 # Disable Line Echo Canceller (LEC). 0 - No, 1 - Yes P824 = 0 # Ring Tone 1 P4010 = c=1000/4000; # Ring Tone 2 P4011 = c=2000/4000; # Ring Tone 3 P4012 = c=2000/4000; # Ring Tone 4 P4013 = c=2000/4000; # Ring Tone 5 P4014 = c=2000/4000; # Ring Tone 6 P4015 = c=2000/4000; # Ring Tone 7 P4016 = c=2000/4000; # Ring Tone 8 P4017 = c=2000/4000; # Ring Tone 9 P4018 = c=2000/4000; # Ring Tone 10 P4019 = c=2000/4000; ############################################################################## ## Profile 2 Settings ############################################################################## # Profile Active. 0 - no, 1 - yes P401 = 0 # Primary SIP Server P747 = sip.mycompany.com # Failover SIP Server P987 = # Prefer Primary SIP Server. 0 - No, 1 - Yes. P4568 = 0 # Outbound Proxy P748 = proxy.mycompany.com # SIP Transport # 0 - UDP, 1 - TCP, 2 - TLS P830 = 0 # NAT Traversal (STUN). 0 - No, 2 - No but send keep-alive, 1 - Yes P730 = 0 # Visual MWI type: 0 - FSK, 1 - Neon P4372 = 0 # DNS Mode. 0 - A Record, 1 - SRV, 2 - NAPTR/SRV. P702 = 0 # SIP User ID is phone number. 0 - no, 1 - yes P763 = 0 # SIP Registration. 0 - no, 1 - yes P731 = 1 # Unregister On Reboot. 0 - no, 1 - yes P752 = 0 # Outgoing call without Registration. 0 - no, 1 - yes P813 = 1 # Register Expiration (in minutes. default 1 hour, max 45 days) P732 = 60 # Registration Retry Wait Time (in seconds. Between 1-3600, default is 30) P471 = 30 # Local SIP port (default 6060) P740 = 6060 # Local RTP port (1024-65535, default 6004) P739 = 6004 # Use Random Port. 0 - no, 1 - yes P778 = 0 # Refer-To Use Target Contact. 0 - no, 1 - yes P469 = 0 # Transfer on Conference Hangup. 0 - no, 1 - yes P4561 = 0 # Remove OBP from Route Header. 0 - no, 1 - yes P4563 =0 # Support SIP Instance ID. 0 - no, 1 - yes P489 = 1 # Validate Incoming Message. 0 - No, 1 - Yes P4341 = 0 # Check SIP Incoming UserID. 0 - No, 1 - Yes P449 = 0 # Allow Incoming SIP Messages from SIP Proxy Only: P742 = 0 # SIP T1 Timeout. RFC 3261 T1 value (RTT estimate) # 50 - 0.5 sec, 100 - 1 sec, 200 - 2 sec, 400 - 4 sec, 800 - 8 sec. Default 100. P440 = 100 # SIP T2 Interval. RFC 3261 T2 value. The maximum retransmit interval for non-INVITE requests and INVITE responses. # 200 - 2 sec, 400 - 4 sec, 800 - 8 sec, 1600 - 16 sec, 3200 - 32 sec. Default 400. P441 = 400 # DTMF Payload Type P779 = 101 # Preferred DTMF method. # 100 - In-audio, 101 - RFC2833, 102 - SIP INFO # Priority 1 P860 = 100 # Priority 2 P861 = 100 # Priority 3 P862 = 100 # Send Flash Event. 0 - no, 1 - yes P774 = 0 # Enable Call Features. 0 - no, 1 - yes P751 = 1 # Proxy-Require (A SIP extension to enable firewall penetration) P792 = # Use NAT IP. This will enable our SIP client to use this IP in the SIP message. Example 64.3.153.50. P866 = # Distinctive Ring Tone # 0 - Ring Tone 1, 1 - Ring Tone 2, 2 - Ring Tone 3, 3 - Ring Tone 4, 4 - Ring Tone 5, # 5 - Ring Tone 6, 6 - Ring Tone 7, 7 - Ring Tone 8, 8 - Ring Tone 9, 9 - Ring Tone 10 # Distinctive Ring Tone Choice 1 P880 = 0 # Choice 1 incoming caller ID P881 = # Distinctive Ring Tone Choice 2 P882 = 0 # Choice 2 incoming caller ID P883 = # Distinctive Ring Tone Choice 3 P884 = 0 # Choice 3 incoming caller ID P885 = # Disable Call Waiting. 0 - no, 1 - yes P791 = 0 # Disable Call-Waiting Caller ID. 0 - no, 1 - yes P823 =0 # Disable Call-Waiting Tone. 0 - no, 1 - yes P817 = 0 # Disable Reminder Ring for On-Hold Call: P4361 = 0 # Disable Visual MWI. 0 - No, 1 - Yes P869 = 0 # Ring Timeout. (10-300, default is 60 seconds) P816 = 60 # Hunting Group Ring Timeout. (5-300, default is 20 seconds) P4331 = 20 # Delayed Call Forward Wait Time. Allowed range 1-120, in seconds. Default 20 seconds. P470 = 20 # No Key Entry Timeout. Default - 4 seconds. P292 = 4 # Early Dial. 0 - No, 1 - Yes (use "Yes" only if proxy supports 484 response). 0 - no, 1 - yes P729 = 0 # Dial Plan Prefix.(this prefix string is added to each dialed number) P766 = # Use # as Dial Key (if set to Yes, "#" will function as the "(Re-)Dial" key). 0 - no, 1 - yes P772 = 1 # Dial Plan P4201 = { x+ | *x+ } # SUBSCRIBE for MWI. 0 - No, 1 - Yes. P709 = 0 # Send Anonymous. 0 - No, 1 - Yes (caller ID will be blocked if set to Yes) P765 = 0 # Anonymous Call Rejection. 0 - No, 1 - Yes. P446 = 0 # Special Feature # 100 - Standard, 108 - CBCOM, 109 - RNK, 111 - Huawei P767 = 100 # Session Expiration (in seconds. default 180 seconds. Allowed value: 90-65535) P434 = 180 # Minimum SE (in seconds. default 90 seconds, must be lower than or equal to P260) P427 = 90 # Caller Request Timer (Request for timer when calling) 0 - no, 1 - yes P428 = 0 # Callee Request Timer (Request for timer when called. i.e. if remote party supports timer but did not request for one) 0 - no, 1 - yes P429 = 0 # Force Timer (Still use timer when remote party does not support timer) 0 - no, 1 - yes P430 = 0 # UAC Specify Refresher. 0 - omit, 1 - UAC, 2 - UAS P432 = 0 # UAS Specify Refresher. 1 - UAC, 2 - UAS P433 = 1 # Force INVITE (Always refresh with INVITE instead of UPDATE even when remote party supports UPDATE) 0 - no, 1 - yes P431 = 0 # Send Re-INVITE After Fax. 0 - No, 1 - Yes P4368 = 0 #------------------------------------------------------------------------------- # Codec/Voice Quality settings #------------------------------------------------------------------------------- # Use First Matching Vocoder in 200OK SDP. 0 - No, 1 - Yes P4364 = 0 # Preferred Vocoder # 0 - PCMU, 8 - PCMA, 4 - G.723, 18 - G.729, 2 - G.726-32, 100 - AAL2-G.726-16, # 102 - AAL2-G.726-24, 104 - AAL2-G726-32, 103 - AAL2-G.726-40, 98 - iLBC, 99 - G.729E # Choice 1. P757 = 0 # Choice 2. P758 = 8 # Choice 3. P759 = 4 # Choice 4. P760 = 18 # Choice 5. P761 = 2 # Choice 6. P762 = 98 # Choice 7. P814 = 103 # Choice 8. P815 = 99 # G723 rate. 0 - 6.3kbps encoding rate, 1 - 5.3kbps encoding rate P749 = 0 # iLBC Frame Size. 0 - 20ms(default), 1 - 30ms. P705 = 0 # iLBC payload type. Between 96 and 127, default is 97. P704 = 97 # AAL2-G726-16 payload type. (between 96 and 127, default is 100) P819 = 100 # AAL2-G726-24 payload type. (between 96 and 127, default is 99) P820 = 99 # AAL2-G726-32 payload type. (between 96 and 127, default is 104) P821 = 104 # AAL2-G726-40 payload type. (between 96 and 127, default is 103) P822 = 103 # G729E payload type. (between 96 and 127, default is 102) P818 = 102 # VAD. 0 - No, 1 - Yes P750 = 0 # Symmetric RTP. 0 - No, 1 - Yes P460 = 0 # FAX Mode. 0 - T.38 (Auto Detect), 1 - Pass Through P710 = 0 # Fax Tone Detection Mode. 1 - Caller, 0 - Callee, 2 - Caller or Callee P895 =0 # Jitter Buffer Type. 0 - Fixed, 1 - Adaptive P831 = 1 # Jitter Buffer Length. 0 - Low, 1 - Medium, 2 - High P832 = 1 # SRTP Mode # 0 = Disabled # 1 = Enabled but not forced # 2 = Enabled and forced P443 = 0 #------------------------------------------------------------------------------- # SLIC Setting # 0 - USA, 1 - AUSTRIA, 2 - BELGIUM, 3 - FINLAND, 4 - FRANCE, 5 - GERMANY # 6 - GREECE, 7 -ITALY, 8 - JAPAN, 9 - NORWAY, 10 - SPAIN, 11 - SWEDEN # 12 - UK, 13 - AUSTRALIA/NEW ZEALAND P864 = 0 # Caller ID Scheme # 0 - Bellcore/Telcordia # 1 - ETSI-FSK during ringing # 2 - ETSI-FSK prior to ringing with DTAS # 3 - ETSI-FSK prior to ringing with LR # 4 - ETSI-FSK prior to ringing with RP # 5 - ETSI-DTMF during ringing # 6 - ETSI-DTMF prior to ringing with DTAS # 7 - ETSI-DTMF prior to ringing with LR # 8 - ETSI-DTMF prior to ringing with RP # 9 - SIN 227 - BT # 10 - NTT Japan P863 = 0 # Polarity Reversal. 0 - No, 1 - Yes P865 = 0 # Loop Current Disconnect. 0 - No, 1 - Yes P893 = 0 # Loop Current Disconnect Duration. In 100 - 10000 milliseconds range, default is 200. P857 = 200 # Hook Flash Timing. In 40-2000 milliseconds range. # minimum P811 = 300 # maximum P812 = 1100 # On Hook Timing. (In 40-2000 milliseconds range, default is 400) P834 = 400 # Gain: # TX # +6dB # +4dB # +2dB # 0dB # -2dB # -4dB # -6dB P248 = 0 # RX # +6dB # +4dB # +2dB # 0dB # -2dB # -4dB # -6dB P283 = 0 # Disable Line Echo Canceller (LEC). 0 - No, 1 - Yes P825 = 0 # Ring Tone 1 P4030 = c=2000/4000; # Ring Tone 2 P4031 = c=2000/4000; # Ring Tone 3 P4032 = c=2000/4000; # Ring Tone 4 P4033 = c=2000/4000; # Ring Tone 5 P4034 = c=2000/4000; # Ring Tone 6 P4035 = c=2000/4000; # Ring Tone 7 P4036 = c=2000/4000; # Ring Tone 8 P4037 = c=2000/4000; # Ring Tone 9 P4038 = c=2000/4000; # Ring Tone 10 P4039 = c=2000/4000; ############################################################################## ## Profile 3 Settings ############################################################################## # Profile Active. 0 - no, 1 - yes P501 = 0 # Primary SIP Server P547 = sip.mycompany.com # Failover SIP Server P997 = # Prefer Primary SIP Server. 0 - No, 1 - Yes. P4569 = 0 # Outbound Proxy P548 = proxy.mycompany.com # SIP Transport # 0 - UDP, 1 - TCP, 2 - TLS P530 = 0 # NAT Traversal (STUN). 0 - No, 2 - No but send keep-alive, 1 - Yes P630 = 0 # Visual MWI type: 0 - FSK, 1 - Neon P4373 = 0 # DNS Mode. 0 - A Record, 1 - SRV, 2 - NAPTR/SRV. P502 = 0 # SIP User ID is phone number. 0 - no, 1 - yes P563 = 0 # SIP Registration. 0 - no, 1 - yes P531 = 1 # Unregister On Reboot. 0 - no, 1 - yes P552 = 0 # Outgoing calls without registration. 0 - No, 1 - Yes P513 = 1 # Register Expiration (in minutes. default 1 hour, max 45 days) P532 = 60 # Registration Retry Wait Time (in seconds. Between 1-3600, default is 30) P571 = 30 # Local SIP port (default 6060) P640 = 6060 # Local RTP port (1024-65535, default 6004) P539 = 6004 # Use Random Port. 0 - no, 1 - yes P578 = 0 # Refer to Use Target Contact. 0 - No, 1 - Yes P569 = 0 # Transfer on Conference Hangup. 0 - no, 1 - yes P4565 = 0 # Remove OBP from Route Header. 0 - no, 1 - yes P4564 =0 # Support SIP Instance ID. 0 - no, 1 - yes P589 = 1 # Validate Incoming Message. 0 - No, 1 - Yes P4342 = 0 # Check SIP Incoming UserID. 0 - No, 1 - Yes (no direct IP calling if Yes) P549 = 0 # Allow Incoming SIP Messages from SIP Proxy Only P4043 = 0 # SIP T1 Timeout. RFC 3261 T1 value (RTT estimate) # 50 - 0.5 sec, 100 - 1 sec, 200 - 2 sec, 400 - 4 sec, 800 - 8 sec. Default 100. P540 = 100 # SIP T2 Interval. RFC 3261 T2 value. The maximum retransmit interval for non-INVITE requests and INVITE responses. # 200 - 2 sec, 400 - 4 sec, 800 - 8 sec, 1600 - 16 sec, 3200 - 32 sec. Default 400. P541 = 400 # DTMF Payload Type P579 = 101 # Preferred DTMF method. # 100 - In-audio, 101 - RFC2833, 102 - SIP INFO # Priority 1 P560 = 100 # Priority 2 P561 = 100 # Priority 3 P562 = 100 # Send FLASH event. 0 - No, 1 - Yes P574 = 0 # Enable Call Features. 0 - no, 1 - yes P551 = 1 # Proxy-Require (A SIP extension to enable firewall penetration) P592 = # Use NAT IP. This will enable our SIP client to use this IP in the SIP message. Example 64.3.153.50. P566 = # Distinctive Ring Tone # 0 - Ring Tone 1, 1 - Ring Tone 2, 2 - Ring Tone 3, 3 - Ring Tone 4, 4 - Ring Tone 5, # 5 - Ring Tone 6, 6 - Ring Tone 7, 7 - Ring Tone 8, 8 - Ring Tone 9, 9 - Ring Tone 10 # Distinctive Ring Tone Choice 1 P580 = 0 # Choice 1 incoming caller ID P581 = # Distinctive Ring Tone Choice 2 P582 = 0 # Choice 2 incoming caller ID P583 = # Distinctive Ring Tone Choice 3 P584 = 0 # Choice 3 incoming caller ID P585 = # Disable Call Waiting. 0 - no, 1 - yes P591 = 0 # Disable Call-Waiting Caller ID. 0 - no, 1 - yes P523 =0 # Disable Call-Waiting Tone. 0 - no, 1 - yes P517 = 0 # Disable Reminder Ring for On-Hold Call: P4362 = 0 # Disable Visual MWI. 0 - No, 1 - Yes P669 = 0 # Ring Timeout. (10-300, default is 60 seconds) P516 = 60 # Hunting Group Ring Timeout. (5-300, default is 20 seconds) P4332 = 20 # Delayed Call Forward Wait Time. Allowed range 1-120, in seconds. Default 20 seconds. P570 = 20 # No Key Entry Timeout. Default - 4 seconds. P492 = 4 # Early Dial. 0 - No, 1 - Yes (use "Yes" only if proxy supports 484 response). 0 - no, 1 - yes P529 = 0 # Dial Plan Prefix (dial plan prefix string). P666 = # Use # as Dial Key (if set to Yes, "#" will function as the "(Re-)Dial" key). 0 - no, 1 - yes P572 = 1 # Dial Plan P4202 = { x+ | *x+ } # SUBSCRIBE for MWI. 0 - No, 1 - Yes. P509 = 0 # Send Anonymous (caller ID will be blocked if set to Yes). 0 - no, 1 - yes P565 = 0 # Anonymous Call Rejection. 0 - No, 1 - Yes. P546 = 0 # Special Feature # 100 - Standard, 108 - CBCOM, 109 - RNK, 111 - Huawei P567 = # Session Expiration (in seconds. default 180 seconds. Allowed value: 90-65535) P534 = 180 # Minimum SE (in seconds. default 90 seconds, must be lower than or equal to P260) P527 = 90 # Caller Request Timer (Request for timer when calling) 0 - no, 1 - yes P528 = 0 # Callee Request Timer (Request for timer when called. i.e. if remote party supports timer but did not request for one) 0 - no, 1 - yes P629 = 0 # Force Timer (Still use timer when remote party does not support timer) 0 - no, 1 - yes P664 = 0 # Force INVITE (Always refresh with INVITE instead of UPDATE even when remote party supports UPDATE) 0 - no, 1 - yes P365 = 0 # UAC Specify Refresher. 0 - omit, 1 - UAC, 2 - UAS P632 = 0 # UAS Specify Refresher. 1 - UAC, 2 - UAS P533 = 1 # Send Re-INVITE After Fax. 0 - No, 1 - Yes P4369 = 0 #------------------------------------------------------------------------------- # Codec/Voice Quality settings #------------------------------------------------------------------------------- # Use First Matching Vocoder in 200OK SDP. 0 - No, 1 - Yes P4365 = 0 # Preferred Vocoder # 0 - PCMU, 8 - PCMA, 4 - G.723, 18 - G.729, 2 - G.726-32, 100 - AAL2-G.726-16, # 102 - AAL2-G.726-24, 104 - AAL2-G726-32, 103 - AAL2-G.726-40, 98 - iLBC, 99 - G.729E # Choice 1. P557 = 0 # Choice 2. P558 = 8 # Choice 3. P559 = 4 # Choice 4. P660 = 18 # Choice 5. P661 = 2 # Choice 6. P662 = 98 # Choice 7. P514 = 103 # Choice 8. P515 = 99 # G723 rate. 0 - 6.3kbps encoding rate, 1 - 5.3kbps encoding rate P4350 = 0 # iLBC Frame Size. 0 - 20ms(default), 1 - 30ms. P505 = 0 # iLBC payload type. Between 96 and 127, default is 97. P504 = 97 # AAL2-G726-16 payload type. (between 96 and 127, default is 100) P519 = 100 # AAL2-G726-24 payload type. (between 96 and 127, default is 99) P520 = 99 # AAL2-G726-32 payload type. (between 96 and 127, default is 104) P521 = 104 # AAL2-G726-40 payload type. (between 96 and 127, default is 103) P522 = 103 # G729E payload type. (between 96 and 127, default is 102) P518 = 102 # VAD. 0 - No, 1 - Yes P550 = 0 # Symmetric RTP. 0 - No, 1 - Yes P691 = 0 # FAX Mode. 0 - T.38 (Auto Detect), 1 - Pass Through P510 = 0 # Fax Tone Detection Mode. 1 - Caller, 0 - Callee, 2 - Caller or Callee P595 =0 # Jitter Buffer Type. 0 - Fixed, 1 - Adaptive P631 = 1 # Jitter Buffer Length. 0 - Low, 1 - Medium, 2 - High P835 = 1 # SRTP Mode # 0 = Disabled # 1 = Enabled but not forced # 2 = Enabled and forced P543 = 0 #------------------------------------------------------------------------------- # SLIC Setting # 0 - USA, 1 - AUSTRIA, 2 - BELGIUM, 3 - FINLAND, 4 - FRANCE, 5 - GERMANY # 6 - GREECE, 7 -ITALY, 8 - JAPAN, 9 - NORWAY, 10 - SPAIN, 11 - SWEDEN # 12 - UK, 13 - AUSTRALIA/NEW ZEALAND P564 = 0 # Caller ID Scheme # 0 - Bellcore/Telcordia # 1 - ETSI-FSK during ringing # 2 - ETSI-FSK prior to ringing with DTAS # 3 - ETSI-FSK prior to ringing with LR # 4 - ETSI-FSK prior to ringing with RP # 5 - ETSI-DTMF during ringing # 6 - ETSI-DTMF prior to ringing with DTAS # 7 - ETSI-DTMF prior to ringing with LR # 8 - ETSI-DTMF prior to ringing with RP # 9 - SIN 227 - BT # 10 - NTT Japan P663 = 0 # Polarity Reversal. 0 - No, 1 - Yes P665 = 0 # Loop Current Disconnect. 0 - No, 1 - Yes P593 = 0 # Loop Current Disconnect Duration. In 100 - 10000 milliseconds range, default is 200. P657 = 200 # Hook Flash Timing. In 40-2000 milliseconds range. # minimum P511 = 300 # maximum P512 = 1100 # On Hook Timing. (In 40-2000 milliseconds range, default is 400) P634 = 400 # Gain: # TX # +6dB # +4dB # +2dB # 0dB # -2dB # -4dB # -6dB P648 = 0 # RX # +6dB # +4dB # +2dB # 0dB # -2dB # -4dB # -6dB P683 = 0 # Disable Line Echo Canceller (LEC). 0 - No, 1 - Yes P4366 = 0 # Ring Tone 1 P4020 = c=2000/4000; # Ring Tone 2 P4021 = c=2000/4000; # Ring Tone 3 P4022 = c=2000/4000; # Ring Tone 4 P4023 = c=2000/4000; # Ring Tone 5 P4024 = c=2000/4000; # Ring Tone 6 P4025 = c=2000/4000; # Ring Tone 7 P4026 = c=2000/4000; # Ring Tone 8 P4027 = c=2000/4000; # Ring Tone 9 P4028 = c=2000/4000; # Ring Tone 10 P4029 = c=2000/4000; ####### ###### ###### ###### ###### ###### ###### ### = #FXS Ports ####### ###### ###### ###### ###### ###### ###### ### = # FXS Port 1 # SIP USER ID, Authenticate ID, Password, Name, Profile ID (0 - Profile 1, 1 - Profile 2, 2 - Profile 3) # Hunting Group (0 - None, 1 - Active, 2 - 2, 3 - 3, 4 -4, 5 - 5, 6 - 6, 7 - 7, 8 - 8 ) P4060 =test P4090 =test P4120 =secret P4180 =Gipsz Jakab P4150 =0 P4300 =0 # FXS Port 2 # SIP USER ID, Authenticate ID, Password, Name, Profile ID (0 - Profile 1, 1 - Profile 2, 2 - Profile 3) # Hunting Group (0 - None, 2 - Active, 1 - 1, 3 - 3, 4 -4, 5 - 5, 6 - 6, 7 - 7, 8 - 8 ) P4061 = P4091 = P4121 = P4181 = P4151 = P4301 = # FXS Port 3 # SIP USER ID, Authenticate ID, Password, Name, Profile ID (0 - Profile 1, 1 - Profile 2, 2 - Profile 3) # Hunting Group (0 - None, 3 - Active, 1 - 1, 2 - 2, 4 -4, 5 - 5, 6 - 6, 7 - 7, 8 - 8 ) P4062 = P4092 = P4122 = P4182 = P4152 = P4302 = # FXS Port 4 # SIP USER ID, Authenticate ID, Password, Name, Profile ID (0 - Profile 1, 1 - Profile 2, 2 - Profile 3) # Hunting Group (0 - None, 4 - Active, 1 - 1, 2 - 2, 3 - 3, 5 - 5, 6 - 6, 7 - 7, 8 - 8 ) P4063 = P4093 = P4123 = P4183 = P4153 = P4303 = #----------------------------------------------------------------------------------------- # The following 4 ports belong to GXW-4008/GXW-4024 only #----------------------------------------------------------------------------------------- # FXS Port 5 # SIP USER ID, Authenticate ID, Password, Name, Profile ID (0 - Profile 1, 1 - Profile 2, 2 - Profile 3) # Hunting Group (0 - None, 5 - Active, 1 - 1, 2 - 2, 3 - 3, 4 -4, 6 - 6, 7 - 7, 8 - 8 ) P4064 = P4094 = P4124 = P4184 = P4154 = P4304 = # FXS Port 6 # SIP USER ID, Authenticate ID, Password, Name, Profile ID (0 - Profile 1, 1 - Profile 2, 2 - Profile 3) # Hunting Group (0 - None, 6 - Active, 1 - 1, 2 - 2, 3 - 3, 4 -4, 5 - 5, 7 - 7, 8 - 8 ) P4065 = P4095 = P4125 = P4185 = P4155 = P4305 = # FXS Port 7 # SIP USER ID, Authenticate ID, Password, Name, Profile ID (0 - Profile 1, 1 - Profile 2, 2 - Profile 3) # Hunting Group (0 - None, 7 - Active, 1 - 1, 2 - 2, 3 - 3, 4 -4, 5 - 5, 6 - 6, 8 - 8 ) P4066 = P4096 = P4126 = P4186 = P4156 = P4306 # FXS Port 8 # SIP USER ID, Authenticate ID, Password, Name, Profile ID (0 - Profile 1, 1 - Profile 2, 2 - Profile 3) # Hunting Group (0 - None, 8 - Active, 1 - 1, 2 - 2, 3 - 3, 4 -4, 5 - 5, 6 - 6, 7 - 7 ) P4067 = P4097 = P4127 = P4187 = P4157 = P4307 = #----------------------------------------------------------------------------------------- # The following 16 ports belong to GXW-4024 only #----------------------------------------------------------------------------------------- # FXS Port 9 # SIP USER ID, Authenticate ID, Password, Name, Profile ID (0 - Profile 1, 1 - Profile 2, 2 - Profile 3) # Hunting Group (0 - None, 5 - Active, 1 - 1, 2 - 2, 3 - 3, 4 -4, 6 - 6, 7 - 7, 8 - 8 ) P4068 = P4098 = P4128 = P4188 = P4158 = P4308 = # FXS Port 10 # SIP USER ID, Authenticate ID, Password, Name, Profile ID (0 - Profile 1, 1 - Profile 2, 2 - Profile 3) # Hunting Group (0 - None, 5 - Active, 1 - 1, 2 - 2, 3 - 3, 4 -4, 6 - 6, 7 - 7, 8 - 8 ) P4069 = P4099 = P4129 = P4189 = P4159 = P4309 = # FXS Port 11 # SIP USER ID, Authenticate ID, Password, Name, Profile ID (0 - Profile 1, 1 - Profile 2, 2 - Profile 3) # Hunting Group (0 - None, 5 - Active, 1 - 1, 2 - 2, 3 - 3, 4 -4, 6 - 6, 7 - 7, 8 - 8 ) P4070 = P4100 = P4130 = P4190 = P4160 = P4310 = # FXS Port 12 # SIP USER ID, Authenticate ID, Password, Name, Profile ID (0 - Profile 1, 1 - Profile 2, 2 - Profile 3) # Hunting Group (0 - None, 5 - Active, 1 - 1, 2 - 2, 3 - 3, 4 -4, 6 - 6, 7 - 7, 8 - 8 ) P4071 = P4101 = P4131 = P4191 = P4161 = P4311 = # FXS Port 13 # SIP USER ID, Authenticate ID, Password, Name, Profile ID (0 - Profile 1, 1 - Profile 2, 2 - Profile 3) # Hunting Group (0 - None, 5 - Active, 1 - 1, 2 - 2, 3 - 3, 4 -4, 6 - 6, 7 - 7, 8 - 8 ) P4072 = P4102 = P4132 = P4192 = P4162 = P4312 = # FXS Port 14 # SIP USER ID, Authenticate ID, Password, Name, Profile ID (0 - Profile 1, 1 - Profile 2, 2 - Profile 3) # Hunting Group (0 - None, 5 - Active, 1 - 1, 2 - 2, 3 - 3, 4 -4, 6 - 6, 7 - 7, 8 - 8 ) P4073 = P4103 = P4133 = P4193 = P4163 = P4313 = # FXS Port 15 # SIP USER ID, Authenticate ID, Password, Name, Profile ID (0 - Profile 1, 1 - Profile 2, 2 - Profile 3) # Hunting Group (0 - None, 5 - Active, 1 - 1, 2 - 2, 3 - 3, 4 -4, 6 - 6, 7 - 7, 8 - 8 ) P4074 = P4104 = P4134 = P4194 = P4164 = P4314 = # FXS Port 16 # SIP USER ID, Authenticate ID, Password, Name, Profile ID (0 - Profile 1, 1 - Profile 2, 2 - Profile 3) # Hunting Group (0 - None, 5 - Active, 1 - 1, 2 - 2, 3 - 3, 4 -4, 6 - 6, 7 - 7, 8 - 8 ) P4075 = P4105 = P4135 = P4195 = P4165 = P4315 = # FXS Port 17 # SIP USER ID, Authenticate ID, Password, Name, Profile ID (0 - Profile 1, 1 - Profile 2, 2 - Profile 3) # Hunting Group (0 - None, 5 - Active, 1 - 1, 2 - 2, 3 - 3, 4 -4, 6 - 6, 7 - 7, 8 - 8 ) P4076 = P4106 = P4136 = P4196 = P4166 = P4316 = # FXS Port 18 # SIP USER ID, Authenticate ID, Password, Name, Profile ID (0 - Profile 1, 1 - Profile 2, 2 - Profile 3) # Hunting Group (0 - None, 5 - Active, 1 - 1, 2 - 2, 3 - 3, 4 -4, 6 - 6, 7 - 7, 8 - 8 ) P4077 = P4107 = P4137 = P4197 = P4167 = P4317 = # FXS Port 19 # SIP USER ID, Authenticate ID, Password, Name, Profile ID (0 - Profile 1, 1 - Profile 2, 2 - Profile 3) # Hunting Group (0 - None, 5 - Active, 1 - 1, 2 - 2, 3 - 3, 4 -4, 6 - 6, 7 - 7, 8 - 8 ) P4078 = P4108 = P4138 = P4198 = P4168 = P4318 = # FXS Port 20 # SIP USER ID, Authenticate ID, Password, Name, Profile ID (0 - Profile 1, 1 - Profile 2, 2 - Profile 3) # Hunting Group (0 - None, 5 - Active, 1 - 1, 2 - 2, 3 - 3, 4 -4, 6 - 6, 7 - 7, 8 - 8 ) P4079 = P4109 = P4139 = P4199 = P4169 = P4319 = # FXS Port 21 # SIP USER ID, Authenticate ID, Password, Name, Profile ID (0 - Profile 1, 1 - Profile 2, 2 - Profile 3) # Hunting Group (0 - None, 5 - Active, 1 - 1, 2 - 2, 3 - 3, 4 -4, 6 - 6, 7 - 7, 8 - 8 ) P4080 = P4110 = P4140 = P4252 = P4170 = P4320 = # FXS Port 22 # SIP USER ID, Authenticate ID, Password, Name, Profile ID (0 - Profile 1, 1 - Profile 2, 2 - Profile 3) # Hunting Group (0 - None, 5 - Active, 1 - 1, 2 - 2, 3 - 3, 4 -4, 6 - 6, 7 - 7, 8 - 8 ) P4081 = P4111 = P4141 = P4253 = P4171 = P4321 = # FXS Port 23 # SIP USER ID, Authenticate ID, Password, Name, Profile ID (0 - Profile 1, 1 - Profile 2, 2 - Profile 3) # Hunting Group (0 - None, 5 - Active, 1 - 1, 2 - 2, 3 - 3, 4 -4, 6 - 6, 7 - 7, 8 - 8 ) P4082 = P4112 = P4142 = P4254 = P4172 = P4322 = # FXS Port 24 # SIP USER ID, Authenticate ID, Password, Name, Profile ID (0 - Profile 1, 1 - Profile 2, 2 - Profile 3) # Hunting Group (0 - None, 5 - Active, 1 - 1, 2 - 2, 3 - 3, 4 -4, 6 - 6, 7 - 7, 8 - 8 ) P4083 = P4113 = P4143 = P4255 = P4173 = P4323 = # Offhook Auto-dial P4210 = P4211 = P4212 = P4213 = P4214 = P4215 = P4216 = P4217 = # Map to FXO Port# P4521 = 1 P4522 = 1 P4523 = 1 P4524 = 1 P4525 = 1 P4526 = 1 P4527 = 1 P4528 = 1 # Map to FXO Gateway IP P4264 = P4265 = P4266 = P4267 = P4268 = P4269 = P4270 = P4271 = # The following is for GXW-4024 only # Offhook Auto-dial P4218 = P4219 = P4220 = P4221 = P4222 = P4223 = P4224 = P4225 = P4226 = P4227 = P4228 = P4229 = P4230 = P4231 = P4232 = P4233 = # Map to FXO Port# P4529 = P4530 = P4531 = P4532 = P4533 = P4534 = P4535 = P4536 = P4537 = P4538 = P4539 = P4540 = P4541 = P4542 = P4543 = P4544 = # Map to FXO Gateway IP P4272 = P4273 = P4274 = P4275 = P4276 = P4277 = P4278 = P4279 = P4280 = P4281 = P4282 = P4283 = P4284 = P4285 = P4286 = P4287 = ####### ###### ###### ###### ###### ###### ###### #### = #Basic Settings Page ####### ###### ###### ###### ###### ###### ###### #### = # End User Password #P196 = 123 # Web Port. Default HTTP is 80. P901 = 80 # Telnet Server. 1 - No, 0 - Yes P276 = 0 #IP Address. 0 - DHCP, 2 - PPPoE, 1 - Static IP P8 = 1 #----------------------------------------------- # DHCP # DHCP Hostname, DHCP option 12. Max length allowed is 32 bytes. P146 = # DHCP Domain Name, DHCP option 15. Max length allowed is 32 bytes. P147 = # DHCP Vendor Class ID, DHCP option 60. Max length allowed is 32 bytes. P148 = HT500 #----------------------------------------------- # PPPoE # PPPoE account ID #P82 = # PPPoE password #P83 = # PPPoE Service Name P269 = # Preferred DNS server P92 = 0 P93 = 0 P94 = 0 P95 = 0 #----------------------------------------------- #Static IP # IP Address. Ignore if DHCP or PPPoE is used P9 = 192 P10 = 168 P11 = 1 P12 = 2 # Subnet mask. Ignore if DHCP or PPPoE is used P13 = 255 P14 = 255 P15 = 255 P16 = 0 # Router. Ignore if DHCP or PPPoE is used P17 = 192 P18 = 168 P19 = 1 P20 = 1 # DNS 1. Ignore if DHCP or PPPoE is used P21 = 193 P22 = 225 P23 = 14 P24 = 58 # DNS 2. Ignore if DHCP or PPPoE is used P25 = 193 P26 = 225 P27 = 13 P28 = 113 #---------------------------------------------------------- # Time Zone. Offset in minutes to GMT # GMT-12:00 (International Date Line West) # GMT-11:00 (Midway Island, Samoa) # GMT-10:00 (US Hawaiian Time) # GMT-9:00 (US Alaska Time) # GMT-8:00 (US Pacific Time, Los Angeles) # GMT-7:00 (US Mountain Time, Denver) # GMT-6:00 (US Central Time, Chicago) # GMT-5:00 (US Eastern Time, New York) # GMT-4:30 (Caracas) # GMT-4:00 (Atlantic Time, Quebec) # GMT-3:30 (Newfoundland) # GMT-3:00 (Greenland) # GMT-2:00 (Mid-Atlantic) # GMT-1:00 (Azores, Cape Verdi Is.) # GMT (London, Dublin, Edinburgh, Lisbon, Casablanca, Monrovia) # GMT+1:00 (Paris, Amsterdam, Berlin, Rome, Vienna, Madrid, Warsaw, Brussels) # GMT+2:00 (Israel, Cairo, Athens, Helsinki, Istanbul, Bucharest) # GMT+3:00 (Moscow, Kuwait, Baghdad, Tehran, Nairobi) # GMT+4:00 (Abu Dhabi, Baku) # GMT-4:30 (Caracas) # GMT+5:00 (Islamabad, Ekaterinburg, Karachi, Tashkent) # GMT+5:30 (Chennai, New Delhi, Mumbai) # GMT+5:45 (Kathmandu) # GMT+6:00 (Almaty, Astana, Dhaka, Novosibirsk) # GMT+6:30 (Rangoon) # GMT+7:00 (Bankok, Jakarta, Hanoi, Krasnoyarsk) # GMT+8:00 (Beijing, Singapore, Taipei, Kuala Lumpur, Irkutsk, Perth) # GMT+9:00 (Japan, Korea, Yakutsk) # GMT+9:30 (Adelaide, Darwin) # GMT+10:00 (Brisbane, Sydney, Melbourne, Canberra, Guam, Hobart) # GMT+11:00 (Magadan, Solomon Is., New Caledonia) # GMT+12:00 (Auckland, Wellington, Fiji) # GMT+13:00 (Nuku'alofa) # Using self-defined Time Zone P64 = customize # Self-Defined Time Zone P246 = CET-1CEST-2,M3.4.0,M10.5.0 # Language. 0 - English, 4 - Chinese, 10 - Spanish IVR P342 = 0 #----------------------------------------------- # NAT/DHCP Server Information & Configuration #----------------------------------------------- # For GXW4004/GXW4008 only #----------------------------------------------- # Device Mode. 0 -NAT Router, 1 - Bridge P231 = 1 # NAT maximum ports. range: 0 - 4096, default is 1024 P896 = 1024 # NAT TCP timeout. range: 0 - 3600, default is 3600 P897 = 3600 # NAT UDP timeout. range: 0 - 3600, default is 300 P898 = 300 # Uplink bandwidth. # Disabled # 128k # 256k # 512k # 1M # 2M # 3M # 4M # 5M # 10M # 15M P867 = 0 # Downlink bandwidth. # Disabled # 128k # 256k # 512k # 1M # 2M # 3M # 4M # 5M # 10M # 15M P868 = 0 # Enable UPnP support. 0 - No, 1 - Yes P890 = 0 # Reply to ICMP on WAN port. 0 - No, 1 - Yes. Unit will not respond to PING from WAN side if set to No. P189 = 0 # WAN side HTTP/Telnet access. 0 - No, 1 - Yes (WAN side access will be rejected if set to No) P190 = 1 # Cloned WAN MAC Addr (in hex format) #P115 = #P116 = #P117 = #P118 = #P119 = #P120 = # Enable LAN DHCP. 0 - No, 1 - Yes P5001 = 1 # LAN DHCP Base IP. (base IP for the LAN port, default is 192.168.2.1) #P111 = 192.168.2.1 # LAN DHCP Start IP. (default is 100) P5002 = 100 # LAN DHCP End IP. (default is 199) P5003 = 199 # LAN Subnet Mask. Default is 255.255.255.0. #P110 = #DHCP IP Lease Time, in units of hours, default is 120 hours or 5 days. #P112 = 120 #DMZ IP. #P113 = #----------------------------------------------------------- # Port Forwarding Settings. #----------------------------------------------------------- ############# Choice 1 #################################### # WAN Port P150 =0 # LAN IP P158 = # LAN Port P166 =0 # Protocol. 0 - UDP Only, 1 - TCP Only, 2 - TCP and UDP. P174 =0 ############# Choice 2 #################################### # WAN Port P151 =0 # LAN IP P159 = # LAN Port P167 =0 # Protocol. 0 - UDP Only, 1 - TCP Only, 2 - TCP and UDP. P175 =0 ############# Choice 3 #################################### # WAN Port P152 =0 # LAN IP P160 = # LAN Port P168 =0 # Protocol. 0 - UDP Only, 1 - TCP Only, 2 - TCP and UDP. P176 =0 ############# Choice 4 #################################### # WAN Port P153 =0 # LAN IP P161 = # LAN Port P169 =0 # Protocol. 0 - UDP Only, 1 - TCP Only, 2 - TCP and UDP. P177 =0 ############# Choice 5 #################################### # WAN Port P154 =0 # LAN IP P162 = # LAN Port P170 =0 # Protocol. 0 - UDP Only, 1 - TCP Only, 2 - TCP and UDP. P178 =0 ############# Choice 6 #################################### # WAN Port P155 =0 # LAN IP P163 = # LAN Port P171 =0 # Protocol. 0 - UDP Only, 1 - TCP Only, 2 - TCP and UDP. P179 =0 ############# Choice 7 #################################### # WAN Port P156 =0 # LAN IP P164 = # LAN Port P172 =0 # Protocol. 0 - UDP Only, 1 - TCP Only, 2 - TCP and UDP. P180 =0 ############# Choice 8 #################################### # WAN Port P157 = 0 # LAN IP P165 = # LAN Port P173 = 0 # Protocol. 0 - UDP Only, 1 - TCP Only, 2 - TCP and UDP. P181 = 0 ##UNKNOWN## # Forcing a Codec per call. *027110 (PCMU), *027111 (PCMA), *02723 (G723), *02729 (G729), *0272616 (G726-r16), *0272624 (G724-r24), *0272632 (G726-r32), *0272640 (G726-r40), *027201 (iLBC) #*02 P4351=*027110 P4352=*027111 P4353=*02723 P4354=*02729 P4355=*0272616 P4356=*0272624 P4357=*0272632 P4358=*0272640 P4359=*021 #unknown P737 =2 P743=0 P229=0 P108=0 P37=2 P245=8 P4306=0 P133=1 P711=0 P4500=0 P4501=1 P4502=0 P200=0 P86=0 P206=2